Here's how to board up windows of wood-framed houses. Tip 1: If you live where hurricanes are a frequent threat, take time during the off season to screw stainless-steel hanger bolts into the framing every 16 inches, and drill matching holes in the plywood. Then, when a storm threatens, you can mount the panels quickly and secure them with nuts and washers.
Because these panels are reusable, prime and paint all surfaces and edges to protect them from decay. Tip 2: On masonry houses, fit the plywood inside the window opening and hold it in place with 4-inch barrel bolts spaced no more than 16 inches apart. Each bolt's sliding shaft fits into a hole drilled in the masonry, not the grout joint.
Cookie banner We use cookies and other tracking technologies to improve your browsing experience on our site, show personalized content and targeted ads, analyze site traffic, and understand where our audiences come from. By choosing I Accept , you consent to our use of cookies and other tracking technologies. How to Board Up Windows for Hurricane. By Mark Feirer. Pinterest Email Pocket Flipboard. Boarding Up Windows For Hurricane Mark the location of the studs closest to each side of and underneath the window.
If there are no nailheads in the siding to give away where the studs are, you'll have to do some probing with a drill and bit. Plywood fastened just to trim or sheathing can go flying. Cut each panel so it will extend at least one inch beyond the framing on all sides of the window. Number each panel to indicate which opening it will cover. Download Article Explore this Article methods. Things You'll Need. Tips and Warnings.
Related Articles. Article Summary. Method 1. Record the vertical and horizontal measurements for the window. Use a tape measure to determine the height and width of the window you plan to board up and write these measurements down. If the window has an extended sill, measure vertically from the top of the sill to the top of the window.
Cut a piece of plywood that is 8 inches 20 cm higher and wider than the window. Add 8 inches 20 cm to the height and width measurements you took of the window, then use these new measurements to measure and cut your plywood. Use a circular saw to cut the plywood. For example, if your window measures 48 inches cm tall and 24 inches 61 cm wide, then your piece of plywood should be 56 inches cm tall and 32 inches 81 cm wide.
If the window has an extended sill, you only need to add 4 inches 10 cm to the height before cutting the plywood. Attach 2 pieces of plywood together if you need a bigger piece. Most pieces of plywood are 4 by 8 feet 1. Place 2 plywood pieces next to each other, then lay a 2 by 4 in 5. Finally, drill 2. Use a stud finder to find the studs in the wall around the window frame.
Look for the studs 4 inches 10 cm out from each side of the window frame. Drill holes in the corners of the plywood that align with the studs. Drill 4 holes that are each around 2 inches 5. You may need to adjust this measurement to ensure that the holes you drill will line up with the studs in the wall when you go to screw in the plywood.
Make additional holes at 12 in 30 cm intervals around the plywood. These holes are where you will screw the plywood into the wall. Align these holes with the corner holes you already drilled to ensure that these new holes will also line up with the studs in the wall. These holes should also be around 2 inches 5. Note that the holes in the top and bottom of the plywood will not be screwed into the studs in the wall. Place the plywood over the window frame and use a drill to screw it in.
Have someone hold the board while you drill screws through each of the pilot holes, or vice versa. Use pan-head or lag screws that will penetrate at least 2 inches 5. Method 2. Determine the height and width of the window with a tape measure, making sure to write your measurements down. Measure from the top of the window frame interior to the bottom, as well as from side to side.
Use a circular saw to cut the plywood to match the height and width of the window frame. For example, if your window frame measures 48 inches cm tall and 24 inches 61 cm wide, then your piece of plywood should be 48 inches cm tall and 24 inches 61 cm wide as well.
Use 2 pieces of plywood attached to each other if the frame is too big. Place 2 plywood pieces next to each other with a 2 by 4 in 5. Then, drill 2. Use a hammer to attach 4 window clips to the sides of the plywood. Place 2 clips on each side of the plywood, positioned so that the tension legs are facing towards you. Then, gently tap the clips with the hammer to attach them to the plywood. Be sure to place each pair of clips no more than 2 feet 0. You may be able to simply push the clips into place.
However, using a hammer will ensure that they are as securely attached to the plywood as possible. Place the plywood over the window frame and push it in to secure it.
Push the plywood as far into the frame as it can go. If the window clips are securely gripping the sides of the frame, they will keep the plywood in place.
Did you know you can get expert answers for this article? Unlock expert answers by supporting wikiHow. Steve Linton Custom Home Builder.
0コメント